Ghost Controls Gate Parts & Welding in Houston, TX

Ghost Controls Gate Parts & Welding in Houston: What to Know First

We provide independent Ghost Controls gate parts and welding service across Houston, with most calls completed in a single visit and pricing settled before we start. A typical hinge replacement or rail weld runs $280-$520, and we stock the common Ghost Controls brackets, arms, and mounting hardware that fail in Houston’s humidity and clay soil. This page is for homeowners running a Ghost Controls TSS1, DTP1, or Architectural Series operator who need the gate itself fixed right, not just the motor reset. Call (888) 799-8389 and a live person will answer, 24 hours a day.

Call (888) 799-8389

How Ghost Controls Products Fail - and How We Fix Them

• TSS1 Heavy-Duty Single Swing: The aluminum actuator arm bracket cracks where it meets the gate frame, especially on heavier ornamental iron gates common in Memorial and River Oaks. Houston’s summer heat cycles expand and contract the metal until the bracket shears. We remove the failed bracket, weld a reinforced steel gusset plate in its place, and realign the operator geometry so the new load path doesn’t repeat the failure.
• DTP1 Dual Swing Systems: The lower hinge pin on the passive leaf wears an oval hole in the jamb post, causing the gate to sag and the Ghost Controls limit switches to lose their reference. We see this constantly in the gumbo clay of Katy and Sugar Land, where posts shift seasonally. Our fix: cut out the damaged hinge pocket, weld in a thicker boss with a grease fitting, and reset the gate plumb so the operator isn’t fighting gravity.
• Architectural Series (AXWK, AXDP): The decorative cover boxes look sharp but trap moisture against the steel frame underneath. After three or four Houston summers, we find rust-jacked welds at the bottom rail and latch stile. We strip the cover, cut out the rot, weld in 14-gauge replacement sections, and drill weep holes the factory forgot.
• GC GHOST CONTROLS standard swing arms: The nylon bushing in the clevis end degrades in UV faster than the company rates it for southern exposure. The arm starts chattering, which loosens the mounting bolts and wallows out the gate-side bracket. We replace with bronze bushing upgrades we machine in-house, weld the bracket flat if it’s not too far gone, or fabricate a new one if it is.
• Gate roller assemblies on Ghost Controls sliding setups: The V-groove rollers seize in the track when Houston’s pollen and road grit pack the bearings. Homeowners keep hitting the remote, and the Ghost Controls motor burns out trying to move a stuck gate. We pull the rollers, weld new mounting tabs if the originals have cracked from the strain, and upgrade to sealed bearings that survive a Houston spring.

Our Ghost Controls Gate Parts & Welding Process

1. 1
   A live person answers your call. We ask what the gate is doing, what series Ghost Controls operator you have, and when you need us there.
2. 2
   On-site diagnosis. Our tech inspects the gate frame, hinges, welds, and operator mounting points, not just the control board. We identify every point of failure, Ghost Controls and otherwise.
3. 3
   Upfront pricing, no surprises. We tell you what parts we need, whether we’re using Ghost Controls OEM brackets or our reinforced fabrication, and what the total is. You approve it before we strike an arc.
4. 4
   The repair. We weld, cut, grind, and fit with the operator’s specs in hand, so the gate moves freely and the Ghost Controls limits and force settings work as designed.
5. 5
   Full-cycle testing. We run the gate through its complete open-close sequence under load, check safety entrapment, and verify the Ghost Controls auto-close timer if you use it.
6. 6
   Written guarantee and cleanup. Every job carries our 90-Day Done Right Promise. We leave the worksite cleaner than we found it.

What Ghost Controls Gate Parts & Welding Costs in Houston

What moves the price: gate material (wrought iron welds slower than aluminum), access for our truck and equipment, and how far the failure has propagated before you call. A cracked hinge caught early is a weld. A hinge ignored for six months usually needs a new post, new gate section, or both. We will tell you what it needs, not what sells. Call (888) 799-8389 for a free estimate, any day, any hour.

Why Houston Homeowners Call Ironworks Gate Co. of Houston for Ghost Controls Work

We are an independent Ghost Controls service provider, not a factory-authorized dealer, which means we fix the gate itself, not just swap warranty parts. Our techs carry Ghost Controls hardware, but they also carry welding rigs and the stock steel to fabricate what no catalog sells. The 90-Day Done Right Promise covers every weld, every part, every adjustment, with no paperwork to file and no argument if something needs tweaking.

Most jobs finish in one visit because our trucks are mobile shops. If your Ghost Controls operator turns out to be the real problem, we are trained and equipped on that too, plus LiftMaster, Mighty Mule, DoorKing, and five other brands, so the correct fix happens on the first trip. Dale Briscoe started this company in 1984, and we have been serving Houston long enough to know which gates in The Heights were hung by the same builder in 1987 and which welds are about to let go.

A live person answers the phone 24 hours a day, 7 days a week. Background-checked, uniformed technicians. Upfront pricing. The Keystone Standard on every job.

FAQs