Linear Gate Parts & Welding in Houston, TX

Linear Gate Parts & Welding in Houston: What to Know First

We provide independent Linear gate parts and welding service across Houston, with most hinge, rail, and post repairs completed in a single visit and upfront pricing settled before we start. A typical Linear gate welding or parts job in Houston runs $280-$650 depending on whether we’re replacing a failed roller on a Linear ACT-31 slide gate or rebuilding the frame on a Linear OSCO swing operator. We will tell you what it needs, not what sells. This page is for Houston homeowners who own a Linear gate system and need straight answers about parts, welding, and what it actually costs to fix it right. Call (888) 799-8389 anytime - a live person answers, day or night.

Call (888) 799-8389

How Linear Products Fail - and How We Fix Them

• Linear ACT-31 slide gate rollers seize in Houston’s humidity. The sealed bearings on these operators weren’t designed for Gulf Coast moisture cycles. We see the roller housing rust-weld itself to the shaft, which then tears the mounting bracket off the gate frame. We replace with marine-grade sealed rollers and weld in a reinforced gusset plate so it doesn’t repeat next spring.
• Linear OSCO swing gate hinge pins wallow out after 8-12 years. The OSCO’s cast-steel hinge boss is softer than the stainless pin, and Houston’s clay soil shifts the post microscopically with every rain. The pin starts to oval the bore. We bore out the boss, press in a hardened steel bushing, and weld the bushing in place with 7018 rod - not the quick MIG tack some guys do that cracks in six months.
• Linear Pro Access control arm brackets crack at the weld. The Pro Access series uses a stamped bracket where the arm meets the gate, and the factory weld is a single-pass fillet. When a teenage driver bumps the gate or wind load cycles it enough, that weld fails clean. We cut off the bracket, grind to clean metal, and lay a multi-pass 6010 root with 7018 fill so the repair outlives the gate.
• Linear HSLG heavy-duty slide gate rails bow from thermal expansion. Houston’s August sun hits 160°F on dark steel rail. The HSLG’s 2-inch square tube rail grows almost 3/8 inch per 20-foot section with nowhere to go. We see the rail push the end rollers off track or pull welds at the post. We cut in an expansion joint with a slip-fit inner sleeve, weld stops at the limits, and reset the operator limit switches so the gate doesn’t hunt for home position.
• Linear LA500 linear actuator mounting feet rip out of brick or stucco columns. The LA500’s bolt pattern concentrates load on four small pads. In Houston, where many estate gates hang on decorative masonry, that concentration pops the anchors. We fabricate a spreader plate from 3/16-inch steel, weld it to the actuator foot, and anchor through the plate with epoxy-set threaded rod into the column core - never into the facade alone.

Our Linear Gate Parts & Welding Process

1. 1
   You call, we answer. A live person at Ironworks Gate Co. of Houston picks up, 24 hours a day. We ask which Linear model you have, what it’s doing, and when you need it working.
2. 2
   On-site diagnosis. Our tech arrives uniformed and background-checked, with a truck stocked for Linear, LiftMaster, Mighty Mule, Ghost Controls, and DoorKing systems. We inspect the gate, the operator, and the structure - not just the symptom.
3. 3
   Parts decision - OEM or quality aftermarket. For Linear, we stock common wear parts: rollers, hinges, actuator feet, limit switches. If your job needs a Linear-specific board or gear assembly, we source OEM. For structural welding and hardware, we use domestic steel and certified weld rod that meets or exceeds factory spec.
4. 4
   Upfront price, your go-ahead. We give you the full cost before touching a bolt. No surprises on the bill. Most Linear parts and welding jobs run $280-$650; major post replacement or custom fabrication runs higher, and we’ll say so.
5. 5
   The repair and the test. We weld, fit, and adjust. Then we cycle the gate 20 times under load, test the safety entrapment, and check the auto-reverse. Linear’s board diagnostics tell part of the story; the gate’s movement tells the rest.
6. 6
   Written 90-Day Done Right Promise. We leave you a copy of our guarantee - the Keystone Standard. If anything’s not right, we come back and make it right. No paperwork to file, no argument.

What Linear Gate Parts & Welding Costs in Houston

What moves the price: gate size and weight (heavier gates need thicker material), access to the work area, whether the post footing is salvageable, and whether the Linear operator itself needs recalibration after structural repair. Houston’s gumbo clay can turn a simple post replacement into a concrete-and-weld job if the footing heaved. We’ll tell you before we start. Call (888) 799-8389 for a free estimate - we’ll come look and give you a firm number.

Why Houston Homeowners Call Ironworks Gate Co. of Houston for Linear Work

We’ve been fixing gates in Houston since 1984. Dale Briscoe started in a welding shop in Acres Homes and learned early that metal work is patience work. That patience shows in how we handle Linear systems - we don’t guess at the wiring diagram, we don’t substitute a “close enough” roller, and we don’t leave a weld looking pretty but hollow inside.

Our 90-Day Done Right Promise is written and given on every job. Our techs are trained on nine automation brands, so if your Linear operator has a secondary issue with a LiftMaster keypad or a DoorKing intercom, we fix it without a second trip. A live person answers our phone at midnight on Sunday. And we show up when we say.

Active offers: $50 off any repair over $250. Free second opinion on any written estimate. $89 seasonal tune-up. Senior and veteran discount of 5%, always.

FAQs